日志
- 分享 the operator is easy to focus on operations
- Plate straightening machine thin chrome work rolls Processing, and Ken, according to process successfully completed 42 0.03-thick chromium layer minister roller production service (86 years of delivery) 89 years and production of spare parts 42, has been used now, clean in good condit ...
- 分享 Medullary billion
- , oakley solbriller Improve the wear resistance of titanium surface treatment technology Medullary billion reduce the inertial mass due to increased speed and power output increase). The recent movement in the golf club components and automotive parts in metal as a new material, so t ...
- 分享 Q [XPeE Song | {W0
- , mulberry oslo J11280 -type 28000kN bedroom cold chamber die casting machine developed ll? elAYVtb @ y: 0? Vt0QEl.l? St? V_Sl.l? tQSRONN Ke Vhl? tvSReAQEl? dO Sc YN? el Meiya YO? V52? u5A Ke Vhm; X ? QvQl.l? SQel ? t0? V52eu5AbS_5P8AT? Ke VhQQEl.l? Av An SRN S4oV2b @ y: I0? Qs Ro ...
- 分享 intelligent operator selection of Panasonic LCD panel
- J213B thermal chamber die casting machine reliability improvements in design After the hydraulic piston and cylinder wall can be maintained between the large gap. Pressure ? 80MPa, the maximum piston speed reciprocating 15m / s, in a 54 a +200'12 temperatures, ed hardy suomessa , seal ...
- 分享 while the air-ling state was 0.58%. 2.5 Fatigue test high-cycle fatigue
- , oakley brasil IMI834 texture of titanium alloy and high temperature mechanical properties of the relationship In the direction of the initial hardening riD higher. Material 1020cC hot, water quenching was significantly higher than the yield stress after air-cooled state. For example ...
- 分享 16MB430 centrifugal casting cylinder
- 16MB430 centrifugal casting cylinder oo0s7-0l diesel engine as an important part of the cylinder with high technical requirements, we must have high strength, high hardness and good microstructure, but also less casting defects. Cylinder used in the past such large-scale sand cast ...
- 分享 ? ? Seoul ? virgin ? Fang ? ? ? ? ?? ? ? ? ? ?? ? ? ???
- ? ? Seoul ? virgin ? Fang ? ? ? ? ?? ? ? ? ? ?? ? ? ?????? ? ? ??? ? monitor Fang ? ? virgin ? tinkling of gems ? ? tinkling of gems ? ? Xiao Yao put ? Bi ? ? ? measured King ?? ? ? ? ? ? ? ? contraction measured Jue ? ? You vortex ? ? ? silicon ingots Su ? ? ? ? ? ? ? ? feet in which Suiyu ? ready. ...
- 分享 time to enter the cold deformation lI
- Cu-Ag-Cr alloy aging characteristics of 0200250300350 aging time / min (b) the impact of heat treatment on the conductivity of heat treatment on 4 Cu-Ag-Cr after aging 480 ? round gold micro-hardness and electrical conductivity of 3 Conclusions (1) Cu a 0.1Ag a 0.46Cr alloy 940ClC ...
- 分享 Be on the 7475 aluminum alloy and Properties
- Be on the 7475 aluminum alloy and Properties n thick hot slab in 350cI =, 2h annealed condition, and then at room temperature under continuous rolling five to 1.5mln thick, cold deformation of 75%, mulberry outlet , then the slab made of 1.5mln 15mln 10rain of a number of smal ...
- 分享 Zhou Yanbang. Aerospace titanium [M]. Shanghai
- B on the titanium-silicon hypoeutectic solidification behavior Compete in the J sharp decrease in the solubility of Ti, si Ti atoms from the solvent in the formation of TiS off phase (?); ? 860 ? when the eutectoid reaction: Ti a formation of a Ti + Ti5Si TiSi phase (eutectoid); ? ...